A carregar...
13 resultados
Resultados da pesquisa
A mostrar 1 - 10 de 13
- Composite material of PDMS with interchangeable transmittance: study of optical, mechanical properties and wettabilityPublication . Sales, Flaminio; Souza, Andrews; Ariati, Ronaldo; Noronha, Verônica Teixeira; Giovanetti, Elder Gulick; Lima, Rui A.; Ribeiro, J.E.Polydimethylsiloxane (PDMS) is a polymer that has attracted the attention of researchers due to its unique properties such as transparency, biocompatibility, high flexibility, and physical and chemical stability. In addition, PDMS modification and combination with other materials can expand its range of applications. For instance, the ability to perform superhydrophobic coating allows for the manufacture of lenses. However, many of these processes are complex and expensive. One of the most promising modifications, which consists of the development of an interchangeable coating, capable of changing its optical characteristics according to some stimuli, has been underexplored. Thus, we report an experimental study of the mechanical and optical properties and wettability of pure PDMS and of two PDMS composites with the addition of 1% paraffin or beeswax using a gravity casting process. The composites’ tensile strength and hardness were lower when compared with pure PDMS. However, the contact angle was increased, reaching the highest values when using the paraffin additive. Additionally, these composites have shown interesting results for the spectrophotometry tests, i.e., the material changed its optical characteristics when heated, going from opaque at room temperature to transparent, with transmittance around 75%, at 70 °C. As a result, these materials have great potential for use in smart devices, such as sensors, due to its ability to change its transparency at high temperatures.
- Numerical characterization of a hyperelastic material to shear stressPublication . Souza, Andrews; Ribeiro, J.E.; Araújo, Fernando F.In last years, some studies have been proved that there is an association between the wall shear stress with intracranial aneurysm rupture, however, is very difficult to understand the mechanical tissue behaviour when subjected to shear stresses. In this work, it is implemented numerical simulations to characterise the polydimethylsiloxane (PDMS) material when it is subjected to a shear solicitation. For this, it was initially necessary to perform some experimental tests to characterize the mechanical behaviour of the material. Based on these results, several numerical simulations were performed with the most common constitutive models in the simulation of hyperelastic materials by varying numerical factors and parameters of the numerical models.
- Characterization of shear strain on PDMS: numerical and experimental approachesPublication . Souza, Andrews; Marques, Eduardo do Carmo; Balsa, Carlos; Ribeiro, J.E.Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in di erent fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behavior stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behavior is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the e ect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four di erent simulations using the Mooney–Rivlin, Yeoh, Gent, and polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviors and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.
- In vitro biomodels in stenotic arteries to perform blood analogues flow visualizations and measurements: a reviewPublication . Carvalho, Violeta Meneses; Maia, Inês; Souza, Andrews; Ribeiro, J.E.; Costa, Pedro; Puga, Hélder Fernandes; Teixeira, Senhorinha F.C.F.; Lima, Rui A.Cardiovascular diseases are one of the leading causes of death globally and the most common pathological process is atherosclerosis. Over the years, these cardiovascular complications have been extensively studied by applying in vivo, in vitro and numerical methods (in silico). In vivo studies represent more accurately the physiological conditions and provide the most realistic data. Nevertheless, these approaches are expensive, and it is complex to control several physiological variables. Hence, the continuous effort to find reliable alternative methods has been growing. In the last decades, numerical simulations have been widely used to assess the blood flow behavior in stenotic arteries and, consequently, providing insights into the cardiovascular disease condition, its progression and therapeutic optimization. However, it is necessary to ensure its accuracy and reliability by comparing the numerical simulations with clinical and experimental data. For this reason, with the progress of the in vitro flow measurement techniques and rapid prototyping, experimental investigation of hemodynamics has gained widespread attention. The present work reviews state-of-the-art in vitro macro-scale arterial stenotic biomodels for flow measurements, summarizing the different fabrication methods, blood analogues and highlighting advantages and limitations of the most used techniques.
- Hemodynamic study in a real intracranial aneurysm: an in vitro and in silico approachPublication . Souza, Andrews; Ribeiro, J.E.; Araújo, Fernando da Silva
- Manufacturing process of a brain aneurysm biomodel in PDMS using rapid prototypingPublication . Souza, Andrews; Ribeiro, J.E.; Lima, Rui A.Cerebral aneurysm is an abnormal dilatation of the blood vessel into a saccular form. They can originate in congenital defects, weakening of the arterial wall with increasing age, atherosclerotic changes, trauma and infectious emboli. The in vivo experiments are an effective way of investigating the appearance, validating new practices and techniques, but beyond ethical issues, these types of experiments are expensive and have low reproducibility. Thus, to better understand the pathophysiological and geometric aspects of an aneurysm, it is important to fabricate in vitro models capable of improving existing endovascular treatments, developing and validating theoretical and computational models. Another difficulty is in the preoperative period of the non-ruptured cerebral aneurysm, known for the success of the skilled acts because there is an anatomical structure of the aneurysm as its current position. Although there are technologies that facilitate three-dimensional video visualization in the case of aneurysms with complex geometries the operative planning is still complicated, so the development of the real three-dimensional physical model becomes advantageous. In this work, the entire process of manufacturing an aneurysm biomodel using polydimethylsiloxane (PDMS) is disassembled by rapid prototyping technology. The manufactured biomodels are able to perform different hemodynamic studies, validate theoretical data, numerical simulations and assist in the preoperative planning.
- Stress Concentration on PDMS: An evaluation of three numerical constitutive models using digital image correlationPublication . Sales, Flaminio; Souza, Andrews; Oliveira, Fallconny Rodrigues Sensato; Lima, Rui A.; Ribeiro, J.E.The examination of hyperelastic materials’ behavior, such as polydimethylsiloxane (PDMS), is crucial for applications in areas as biomedicine and electronics. However, the limitations of hyperelastic models for specific stress scenarios, with stress concentration, are not well explored on the literature. To address this, firstly, three constitutive models were evaluated (Neo-Hookean, Mooney-Rivlin, and Ogden) using numerical simulations and Digital Image Correlation (DIC) analysis during a uniaxial tensile test. The samples were made of PDMS with stress concentration geometries (center holes, shoulder fillets, and edge notches). Results of ANOVA analysis showed that any of the three models can be chosen for numerical analysis of PDMS since no significant differences in suitability were found. Finally, the Ogen model was chosen to obtain the stress concentration factors for these geometries, a property which characterize how discontinuities change the maximum stress supported by an element. Our study provides new values for variables needed to analyze and design hyperelastic elements and produce a foundation for understanding PDMS stress-strain behavior.
- Coolant flow in structured grinding wheels: CFD validation via high-speed imaging and particle trackingPublication . Costa, Sharlane; Souza, Andrews; Neves, Lucas B.; Ribeiro, J.E.; Pereira, Mário; Soares, DelfimEfficient coolant delivery is essential in grinding to control heat generation, minimize tool wear, and preserve workpiece integrity. However, Computational Fluid Dynamics (CFD) models commonly used for coolant system design remain rarely validated due to the extreme speeds and complex multiphase flows involved. This work addresses this gap by combining CFD simulations with targeted experiments to evaluate heat removal effectiveness in internally cooled grinding wheels with three channel inclinations: positive, straight, and negative. Transparent resin prototypes enabled high-speed imaging and particle tracking for flow field validation, while grinding tests measured temperature rise and mechanical loads. Results demonstrate that channel inclination strongly affects fluid acceleration, jet coherence, and penetration into the grinding zone, with the positive inclination producing the highest outlet velocities and reducing temperature rise by up to 67%. Particle tracking confirmed CFD predictions within 16% deviation, validating the model’s reliability. By establishing a direct correlation between coolant jet dynamics, heat dissipation, and process performance, this study demonstrates a methodology for the thermal optimization of internal cooling systems in rotating tools. The approach provides a pathway for improving energy efficiency, extending tool life, and reducing coolant consumption in industrial machining processes.
- Tunable physicochemical properties of PDMS@nanoparticle composites: modifications, mechanisms, and emerging applicationsPublication . Cardoso, B.D.; Nobrega, Glauco; Afonso, Inês Santos ; Souza, Andrews; Neves, Lucas B.; Faria, C.L.; Díaz de Tuesta, Jose Luis; Ribeiro, J.E.; Lima, Rui A.Polydimethylsiloxane@nanoparticles (PDMS@NPs) composites represent a versatile class of advanced elastomers whose physicochemical behavior can be finely tuned through nanoscale interfacial design and nanofiller morphology. Owing to their inherent flexibility, transparency, and chemical stability, PDMS based systems have emerged as model platforms for developing multifunctional materials with optimized mechanical, thermal, electrical, optical, acoustic and wetting properties. This review systematically elucidates the structure property relationships in PDMS@NPs composites and the interaction mechanisms between NPs and polymer chains that enable tunable control over bulk and interfacial behavior, with particular emphasis on how NPs dimensionality and aspect ratio (0D, 1D, and 2D fillers) regulate stress transfer, transport pathways, and functional interconnectivity within the matrix. Three main NP incorporation strategies, (namely, physical mixing of presynthesized NPs, in situ synthesis on cured PDMS, and in situ formation within uncured matrices) are critically compared in terms of interfacial coupling, dispersion stability, and processing scalability. Particular attention is given to how interfacial engineering, nanofiller morphology, and hierarchical architecture govern stress transfer, phonon transport, charge percolation, and optical or surface responses. In addition, a property design prospective is presented that links interphase design and nanofiller morphology to mechanical, thermal, electrical, optical, acoustic and wetting-controlled surface properties. This review further critically examines the limiting factors that reduce the applicability of PDMS@NPs composites, including performance degradation, interface instability, and limited recyclability, as well as long-term stability under mechanical, thermal, optical, and environmental conditions. Emerging directions such as green filler synthesis, recyclable PDMS matrices, dynamic and hi-erarchical interphases, and predictive modeling of morphology-dependent dynamic interfaces are outlined. Overall, this review provides a comprehensive and critical perspective on PDMS@NPs composites as a next generation of soft, functional, and sustainable elastomeric materials, opening new avenues for advances in flexible electronics, soft robotics, biomedical devices, and adaptive coatings.
- Progress in Nanofluid Technology: From Conventional to Green Nanofluids for Biomedical, Heat Transfer, and Machining ApplicationsPublication . Cardoso, Beatriz D.; Souza, Andrews; Nobrega, Glauco; Afonso, Inês Santos ; Neves, Lucas B.; Faria, Carlos; Ribeiro, J.E.; Lima, Rui A.Nanofluids (NFs), consisting of nanoparticles (NPs) suspended in base fluids, have attracted growing interest due to their superior physicochemical properties and multifunctional potential. In this review, conventional and green NF technology aspects, including synthesis routes, formulation, and applications, are discussed. Conventional NFs, involving NPs synthesized using physical and chemical approaches, have improved NP morphology control but are likely to cause environmental and safety concerns. In contrast, green NFs that are plant extract, microorganism, and biogenic waste-based represent a sustainable and biocompatible alternative. The effect of key parameters (e.g., NP size, shape, concentration, dispersion stability, and base fluid properties) on the performance of NFs is critically examined. The review also covers potential applications: in biomedical engineering (e.g., drug delivery, imaging, theranostics, and antimicrobial therapies), in heat transfer (e.g., solar collectors, cooling electronics, nuclear reactors), and precision machining (e.g., lubricants and coolants). Comparative insights regarding green versus conventionally prepared NFs are provided concerning their toxicity, environmental impact, scalability, and functional performance across various applications. Overall, this review highlights the new promise of both green and conventional NFs and provides key opportunities and challenges to guide future developments in this field.